Page 2 of 2

Posted: Mon Dec 24, 2007 11:46 am
by Lucas_arts_182
ive had a look at the software for the 400pro , and i got the hang of it inside 30 seconds even though im only 15 :D , so you think that a tech or anyone for that matter that has the authority to use these frequncies would have the mental capacity to figure out how to use the software properly , ive been told that its $10,000 fine or/and 2 years jail if you caught TXing on a emergency service frequncie without permission

Posted: Mon Dec 24, 2007 12:30 pm
by vk6hgr
Lucas_arts_182 wrote:ive been told that its $10,000 fine or/and 2 years jail if you caught TXing on a emergency service frequncie without permission
Actually, under the Radiocommunications Act, you can be fined and/or gaoled just for connecting a radio programmed for transmission on any frequencies you're not authorised for to an antenna.

Posted: Tue Jan 01, 2008 9:39 pm
by Icom-Luke
lol TX on police channels how stupid do you think I am I wouldnt even attempt that I told you straight up what I wanted it for but again people assume I am trying to do bad. And for the record I am not a 15 year old kid thankyou.

Posted: Wed Jan 02, 2008 10:52 am
by Bonez
vk6hgr wrote:
Lucas_arts_182 wrote:ive been told that its $10,000 fine or/and 2 years jail if you caught TXing on a emergency service frequncie without permission
Actually, under the Radiocommunications Act, you can be fined and/or gaoled just for connecting a radio programmed for transmission on any frequencies you're not authorised for to an antenna.
Very interesting... so if I have an all-mode-all-band amateur transciever, can I get in trouble for connecting it because it's programmed for bands that i'm not licensed on?

Grey area huh! :lol:

Posted: Wed Jan 02, 2008 12:50 pm
by vk6hgr
Bonez wrote: Very interesting... so if I have an all-mode-all-band amateur transciever, can I get in trouble for connecting it because it's programmed for bands that i'm not licensed on?
Technically, yes. :lol:

Posted: Wed Jan 02, 2008 3:13 pm
by Icom-Luke
Lucas_arts_182 wrote:ive had a look at the software for the 400pro , and i got the hang of it inside 30 seconds even though im only 15 :D , so you think that a tech or anyone for that matter that has the authority to use these frequncies would have the mental capacity to figure out how to use the software properly , TOOL, ive been told that its $10,000 fine or/and 2 years jail if you caught TXing on a emergency service frequncie without permission

Congrats on picking up in a 30 sec time frame even tho my question wasn't in regards on how to use the program it was how to TX a channel in regards to the quote "TOOL" I don't think there is any need for yourself to express your thoughts on the forum out loud best keep them to yourself and to everyone else I am not an idiot and don't wish to TX on any emergency service channel I simply asked to know for further knowledge and for the reason I put forward to the forum at the start of this Post

Posted: Wed Jan 02, 2008 4:45 pm
by Lucas_arts_182
im just trying to say how easy it is to figure out.
do you know what inhabit means? or what about TX?
have you even had a look at help/trouble-shooting?

Some text deleted by admin due to its inappropriate nature.

Posted: Sat Oct 11, 2008 1:54 pm
by vk5freq
i was not aware of the tx programming of the ic400 pro is it capable of tx mods

Re: Programming the ICOM IC400 pro

Posted: Fri Dec 19, 2008 1:51 pm
by nra555
Yes, the Icom IC-400pro is a commercial radio and can transmitt on UHF Commercial frequencies.

Re:

Posted: Tue Dec 23, 2008 6:59 pm
by Mug
Icom-Luke wrote:
Lucas_arts_182 wrote:ive had a look at the software for the 400pro , and i got the hang of it inside 30 seconds even though im only 15 :D , so you think that a tech or anyone for that matter that has the authority to use these frequncies would have the mental capacity to figure out how to use the software properly , TOOL, ive been told that its $10,000 fine or/and 2 years jail if you caught TXing on a emergency service frequncie without permission

Congrats on picking up in a 30 sec time frame even tho my question wasn't in regards on how to use the program it was how to TX a channel in regards to the quote "TOOL" I don't think there is any need for yourself to express your thoughts on the forum out loud best keep them to yourself and to everyone else I am not an idiot and don't wish to TX on any emergency service channel I simply asked to know for further knowledge and for the reason I put forward to the forum at the start of this Post
I assume the fullstop key on your keyboard is broken?

Re: Re:

Posted: Tue Dec 23, 2008 7:35 pm
by Always RX
Mug wrote:I assume the fullstop key on your keyboard is broken?
I think what Mug actually meant to say was "could you please punctuate your sentances to make them a little bit easier to read".

Re: Programming the ICOM IC400 pro

Posted: Tue Dec 23, 2008 11:20 pm
by Zebedee
Ouch. Old thread. Needs locking.