Setting up the shack
Posted: Tue Apr 07, 2009 8:33 am
I do, it has UHF plugs on it so you'll need adapters.Tyranus wrote:do you have a meter I can borrow??...oh and most of the connections are BNC.
WA Radio Scanner Users' Group
Providing a voice for responsible scanner users in Western Australia
https://warsug.info/
Setting up the shack
Page 1 of 1
Re: Setting up the shack
Posted: Tue Apr 07, 2009 2:20 pm
Note: Just split this and created another thread as the repeater coverage thread was headed off topic because of yours truly...again 
before long I'll be seeing the 2 admins at the HARG and be getting my hands smacked! 
Ok thanks meg, if I can borrow it off you when i'm doing my big mounts and runs of cable that would be great! I'm just going to use the other RG58 with BNC's for my scanner.
before long I'll be seeing the 2 admins at the HARG and be getting my hands smacked! Ok thanks meg, if I can borrow it off you when i'm doing my big mounts and runs of cable that would be great! I'm just going to use the other RG58 with BNC's for my scanner.
Re: Setting up the shack
Posted: Tue Apr 07, 2009 4:49 pm
You're on mast duty... and the rotator needs a good dusting. And that's for the promotion!Tyranus wrote:before long I'll be seeing the 2 admins at the HARG and be getting my hands smacked!
Re: Setting up the shack
Posted: Tue Apr 07, 2009 5:06 pm
No worries - let me know when you'll need itTyranus wrote: Ok thanks meg, if I can borrow it off you when i'm doing my big mounts and runs of cable that would be great
Re: Setting up the shack
Posted: Tue Apr 07, 2009 11:55 pm
Well went and had a look at the tower...and met Ivan VK6FIVN it's not a windy up/down mast such as at the harg, it's a fixed sectional mast with each section being a couple of metres or there abouts in length. so I should be able to put 2 or 3 sections together without a problem and hopefully the shire will let me do 4 or 5. If I remember correctly there's about 6 sections all up. Looks in pretty good nick apparently was once upon a time destined for an oil/gas rig. There's a couple of slight bends but otherwise it's not bad.
I'll pick it up tomorrow evening. Need to check heights with the shire though, so no assembling just yet
. Then there's the decision of things like when do I get the rotator etc. but first things first, tower!
I'll pick it up tomorrow evening. Need to check heights with the shire though, so no assembling just yet
. Then there's the decision of things like when do I get the rotator etc. but first things first, tower!Re: Setting up the shack
Posted: Wed Apr 08, 2009 5:58 am
How do you get to the top? Lower it or climb it?
Re: Setting up the shack
Posted: Wed Apr 08, 2009 10:19 am
lower/tilt the bottom has a plate with a hinge setup.
Restrictions are: Not higher than 5m and the yagi's maximum diameter is 1.5m.
Not too sure on the height of our roof, so might have to do some long way round working.
Restrictions are: Not higher than 5m and the yagi's maximum diameter is 1.5m.
Not too sure on the height of our roof, so might have to do some long way round working.
Re: Setting up the shack
Posted: Sun May 10, 2009 3:21 pm
You might want to read through this case which was won by an amateur against his council a few years ago for a much higher mast - could be useful as a precedent even though it was in Vic.Tyranus wrote: Restrictions are: Not higher than 5m and the yagi's maximum diameter is 1.5m.
Not too sure on the height of our roof, so might have to do some long way round working.
http://www.austlii.edu.au/cgi-bin/sinod ... aciszewski
Re: Setting up the shack
Posted: Sun Jul 19, 2009 7:16 pm
This is as good a place as any ... don't forget to batten down your antennae this evening. Storm warning etc. Thanks meg for reminding me, now that I have something to batten down.