Folks,
I've been meaning to get around to doing this for a while since I've been asked a couple of times now about how my radio is installed in the car. So I got my camera out this morning and took some photos. All of the pictures in this post are clickable so you can see a larger version, without making the page take ages to load to begin with...
The vehicle is a standard BA Falcon sedan, and the radio is a Yaesu FT-7800R with the separation kit so the head unit can be mounted remotely.
Here's how it appears, as you look into the car - it's fairly discreet, so it doesn't stand out too much.
The head unit sits in the tissue box holder, held in place with a strip of double-sided tape on the underside. A small hole was cut into the back of the tissue box holder for the separation kit cable to run through.
The speaker is from an old Nokia car kit - I haven't run the cable for that properly yet, it's just appearing over the top of the centre console and then under to the front passenger seat. I'll get around to tidying that up one day!
The cable runs under the centre console , re-appearing under the passenger seat, where the radio itself is mounted. The other cables that run here are power (direct from the car's battery) and the antenna cable. In each case, the cables run under the plastic trim. Like a lot of newer cars, they helpfully leave little channels here and there to run extra cables
This is the antenna on the outside of the car. It's a 2m/70cm dual band steel whip antenna which I bought from Andrews Communications in Sydney.
The antenna is mounted on a bracket made by GME which is specifically shaped for a BA Falcon which is handy... They make them in driver's or passenger's side configuration.
The antenna cable you can see above was run under some channel in the plastic grille, and it pokes out through a rubber elbow grommet and then cable-tied to handy bits of pipe-work to keep it all neat as it heads towards another grommet in the firewall so it can pass into the passenger cabin.
I decided I wanted the radio to be powered independently of the rest of the car's systems, so instead of taking the power from the accessories circuit, it has it's own wire running straight to the battery.
Of course the danger here is that you could leave the radio on and flatten the car battery overnight - so I've set the radio's timer to shut off after 1 hour of no use...
Again, the power cable is cable-tied to other cables or pipes running towards the grommet in the firewall, so that everything's nice and neat and not flapping around in the engine bay. The grommet has a hole expertly punctured in it with a screwdriver
And that's it!
Holes required to do this - two in the bodywork where the antenna bracket is mounted, one in the elbow grommet for the antenna cable, one in the grommet in the firwall for the antenna and power cables, and one in the back of the tissue box holder for the separation kit cable. Total of five
Yaesu FT7800R installation into BA Falcon
Moderator: VK6ZMS
-
- Site Admin
- Posts: 3022
- Joined: Thu Feb 24, 2005 10:42 pm
- Amateur callsign: VK6DB
- Location: Perth
- Contact:
Yaesu FT7800R installation into BA Falcon
Doug Bell (Zebedee) VK6DB
WARSUG Forum Administrator.
It is very dark.
You are likely to be eaten by a grue.
WARSUG Forum Administrator.
It is very dark.
You are likely to be eaten by a grue.
-
- Posts: 122
- Joined: Mon Mar 10, 2008 1:31 am
- Location: UHF 16
You mention running a 12v power straight to the battery. I assume it's fused and has a toggled on/off switch?
Other than that, a very very tidy install. I need to get around to installing a UHF/similar radio of some sort in my Falcon. I have an earlier model but the interior and engine bay is almost a carbon copy of your BA (2002 AU).
Looks the goods! Nice and tidy!
Other than that, a very very tidy install. I need to get around to installing a UHF/similar radio of some sort in my Falcon. I have an earlier model but the interior and engine bay is almost a carbon copy of your BA (2002 AU).
Looks the goods! Nice and tidy!
-
- Site Admin
- Posts: 3022
- Joined: Thu Feb 24, 2005 10:42 pm
- Amateur callsign: VK6DB
- Location: Perth
- Contact:
Fuse - yep. In fact the inline fuse holder is visible just where the wire comes off the battery terminal. It's partially hidden under the small heater hoses in the picture.Clontarf[X] wrote:You mention running a 12v power straight to the battery. I assume it's fused and has a toggled on/off switch?
Toggle switch - no. Not interested in that.
Thanks for the kind words though about the neatness of the install... However I can't claim the credit, my brother did just about all of it for me, he's much better at that kind of thing than I am
Doug Bell (Zebedee) VK6DB
WARSUG Forum Administrator.
It is very dark.
You are likely to be eaten by a grue.
WARSUG Forum Administrator.
It is very dark.
You are likely to be eaten by a grue.
-
- Moderator
- Posts: 1628
- Joined: Fri Jan 13, 2006 1:15 am
- Location: Greenmount
-
- Site Admin
- Posts: 3022
- Joined: Thu Feb 24, 2005 10:42 pm
- Amateur callsign: VK6DB
- Location: Perth
- Contact:
Haha spot onauntys_eyes wrote:Obviously don't have kids then Zeb That install under the seat would be kicked out in seconds in our family wagon
There's no reason why it couldn't have gone in the boot though, that'd work just as well. From memory there was plenty of cable that came with the separation kit for it to run all the way back there.
But under the seat seemed to be the easiest option at the time
Doug Bell (Zebedee) VK6DB
WARSUG Forum Administrator.
It is very dark.
You are likely to be eaten by a grue.
WARSUG Forum Administrator.
It is very dark.
You are likely to be eaten by a grue.
Way too neat...! It should look something like this:
http://www.flickr.com/photos/22843657@N00/254068953/
http://www.flickr.com/photos/22843657@N ... otostream/
http://www.flickr.com/photos/22843657@N ... otostream/
http://www.flickr.com/photos/22843657@N00/254068953/
http://www.flickr.com/photos/22843657@N ... otostream/
http://www.flickr.com/photos/22843657@N ... otostream/
Last edited by VK6LD on Tue Jan 10, 2012 6:38 pm, edited 1 time in total.
-
- Moderator
- Posts: 2993
- Joined: Sat Feb 09, 2008 10:06 am
- Amateur callsign: VK6UFO_VK6RN
- Scanners and Receivers:
Scanners/receivers
Diamond Welz WS1000 wideband handheld
Radioshack Pro 28 handheld
Uniden UBC72XLT handheld
Uniden UBC73XLT handheld
Uniden UBC330CRS desktop
Two-way
Yaesu VX-3R 2m/70cm Ham TRX and wideband RX handheld
Yaesu FT-1802M 2m Ham TRX mobile x 2
Yaesu FT-7800R 2m/70cm Ham TRX and wide band RX mobile
Icom IC-208H 2m/70cm Ham TRX and wide band RX mobile
Icom IC-706MKIIG all-band all-mode Ham TRX mobile
Icom IC-V85 2m VHF Ham TRX handheld
Wouxun KG-UVD1P VHF/UHF wideband Ham TRX handheld
Wouxun KG-679P VHF wideband Ham TRX handheld
Wouxun KG-713 UHF wideband Ham TRX handheld - Location: Just on the border of your waking mind
Check out the photo gallery on www.hamsexy.com for some more whacker mobiles!Zebedee wrote:Good god...
I used to have four antennae on my old car and I thought that was bad enough (Car radio, UHF CB, Scanner, GSM phone)
I did tell Gav one time that I was going to put a pic of his old Commodore on there...
-
- Moderator
- Posts: 3746
- Joined: Sun Feb 18, 2007 5:41 pm
- Amateur callsign: VK6FWDH
- Scanners and Receivers: UBC93XLT
- Location: Helena Valley
- Contact:
Funnily enough that's what my SES mates call my car previously it was an alien because I had 2 magnetic bases at the back with 400MHz aerials. Bearing in mind I have a Hyundai Getz. Now i've got 2 aerial's next 2 each other by the bonnet. Same story as Gav though: Car radio, Mobile phone; UHF CB; Scanner...eventually No.5 for HAM but probably only when I've got my standard license.WPXZBP wrote:Yeah, I don't want my car to be called a porcupine any more!
Stirling SES
Team Leader (Stirling 53)
Vertical Rescue Team Member
K9 7 Support
VK6FWDH
ex-Darlington FB
WARSUG Demi-God I mean Mod
If stupidity got me into this mess, why can't it get me out.
Team Leader (Stirling 53)
Vertical Rescue Team Member
K9 7 Support
VK6FWDH
ex-Darlington FB
WARSUG Demi-God I mean Mod
If stupidity got me into this mess, why can't it get me out.
-
- Moderator
- Posts: 2993
- Joined: Sat Feb 09, 2008 10:06 am
- Amateur callsign: VK6UFO_VK6RN
- Scanners and Receivers:
Scanners/receivers
Diamond Welz WS1000 wideband handheld
Radioshack Pro 28 handheld
Uniden UBC72XLT handheld
Uniden UBC73XLT handheld
Uniden UBC330CRS desktop
Two-way
Yaesu VX-3R 2m/70cm Ham TRX and wideband RX handheld
Yaesu FT-1802M 2m Ham TRX mobile x 2
Yaesu FT-7800R 2m/70cm Ham TRX and wide band RX mobile
Icom IC-208H 2m/70cm Ham TRX and wide band RX mobile
Icom IC-706MKIIG all-band all-mode Ham TRX mobile
Icom IC-V85 2m VHF Ham TRX handheld
Wouxun KG-UVD1P VHF/UHF wideband Ham TRX handheld
Wouxun KG-679P VHF wideband Ham TRX handheld
Wouxun KG-713 UHF wideband Ham TRX handheld - Location: Just on the border of your waking mind
Have you checked the SWR of your CB antenna? Those two are so close you are likely getting interaction. I think the rule is - minimum of 1/4 wavelength between antennas (~158mm for UHF CB)Tyranus wrote:Now i've got 2 aerial's next 2 each other by the bonnet.
Rob
OF78WD
Amateur moderator
.
→Arguing with a fool proves there are two
OF78WD
Amateur moderator
.
→Arguing with a fool proves there are two
-
- Moderator
- Posts: 3746
- Joined: Sun Feb 18, 2007 5:41 pm
- Amateur callsign: VK6FWDH
- Scanners and Receivers: UBC93XLT
- Location: Helena Valley
- Contact:
Nope and I use the cb that infrequently...hardly ever! that if the other one or something is absorbing some of the radio waves or reflecting them then it doesn't matter.robbage wrote:Have you checked the SWR of your CB antenna? Those two are so close you are likely getting interaction. I think the rule is - minimum of 1/4 wavelength between antennas (~158mm for UHF CB)Tyranus wrote:Now i've got 2 aerial's next 2 each other by the bonnet.
Stirling SES
Team Leader (Stirling 53)
Vertical Rescue Team Member
K9 7 Support
VK6FWDH
ex-Darlington FB
WARSUG Demi-God I mean Mod
If stupidity got me into this mess, why can't it get me out.
Team Leader (Stirling 53)
Vertical Rescue Team Member
K9 7 Support
VK6FWDH
ex-Darlington FB
WARSUG Demi-God I mean Mod
If stupidity got me into this mess, why can't it get me out.