Introducing the Uniden UBC93XLT Scanner

A section for forum members to post reviews of equipment they own or have owned.

Moderator: Nafenn

spartacus
WARSUG top poster
WARSUG top poster
Posts: 941
Joined: Sat Jul 14, 2007 1:15 pm
Amateur callsign: ONEDAYILLGETIT
Scanners and Receivers: ubc92xlt
Location: BOO!!

Re: Introducing the Uniden UBC93XLT Scanner

Post by spartacus »

May I just add that I realized at the Skyshow this year that this radio does not do the FM radio broadcast range - 88MHz till 108MHz.
To stop displaying signatures, go to the User Control Panel > Board Preferences > Edit display options > Display signatures > No > Submit
Sloand
Posts: 2
Joined: Sat May 12, 2012 9:53 am
Scanners and Receivers: Uniden UBC93XLT

Re: Introducing the Uniden UBC93XLT Scanner

Post by Sloand »

I have a problem guys, hoping someone can assist me in recovering my 93xlt...

It was working fine and I was getting heaps of signal breaking in through the channels I was scanning, so I started trying to lockout channels....

Bad mistake, next time I'll wear my glasses so I can what buttons I'm hitting. :-(

Scanner turns on and off fine, beeps on, beeps off. Other than that, no sound, no signals located.

I reset with the 2 -9 - Hold - Power for 3 seconds, "clear" appeared, beeped and turned on. All preprogrammed (by me) gone, as warned.

Still the same, squelch wide open, volume up, no hiss, programmed a UHF CD frequency, turned UHF CB transceiver on to same, transmitted, scanner ignored it.

HELP!!! What have I done? What can I do to restore it?

Chris
colin
150+ posts
150+ posts
Posts: 223
Joined: Sun Dec 09, 2007 2:33 pm
Amateur callsign: VK6FITN
Scanners and Receivers: RTL2832U with RTL_Airband
Tait 8200
Location: Bakers Hill
Contact:

Re: Introducing the Uniden UBC93XLT Scanner

Post by colin »

Dumb question, but have you checked your antenna?
Colin.
Sloand
Posts: 2
Joined: Sat May 12, 2012 9:53 am
Scanners and Receivers: Uniden UBC93XLT

Re: Introducing the Uniden UBC93XLT Scanner

Post by Sloand »

colin wrote:Dumb question, but have you checked your antenna?
Yup.

But now it's weird. One for the memory banks, the human ones. :-)

I left it on scanning bank 6 and after a couple of hours, received a signal. Oh Joy! It's working again.

Weird. Coincidentally the rechargeable batteries went low, it started bipping the warning.

Another set of freshly charged batteries in, reprogramming and it's fine.

Weird. I'm wondering if one of the batteries is bad or one was charged the other not. I may be on the wrong tram but it's all I can figure.

Thanks for your reply. :-)

Chris
btw, I'm in Melbourne but this forum was the only site I could find that mentioned this critter.
henkilook
Posts: 1
Joined: Thu Nov 18, 2021 6:47 pm
Scanners and Receivers: Scanners

Re: Introducing the Uniden UBC93XLT Scanner

Post by henkilook »

How do I reset my Uniden scanner?
So check out my rad 140 results and find out more about it. visit here for andarine s4 sarm
JhG123
150+ posts
150+ posts
Posts: 253
Joined: Mon Oct 29, 2018 8:20 pm

Re: Introducing the Uniden UBC93XLT Scanner

Post by JhG123 »

henkilook wrote: Thu Nov 18, 2021 6:49 pm How do I reset my Uniden scanner?
Which model? If it's the 93XLT, power off the scanner and hold "2", "9" and "HOLD" while you power it on. That should reset it.
reena 20
Posts: 1
Joined: Tue Mar 01, 2022 12:42 am
Amateur callsign: no
Scanners and Receivers: Uniden BCD436HP HomePatrol Series Digital Handheld Scanner

Re: Introducing the Uniden UBC93XLT Scanner

Post by reena 20 »

I still use my Uniden UBC93XLT Scanner. I must say about it, old is Gold. :)

This phen24 review
Last edited by reena 20 on Tue Sep 05, 2023 6:40 pm, edited 1 time in total.
rustynswrail
Posts: 75
Joined: Thu Oct 04, 2007 8:25 am
Location: Right here

Re: Introducing the Uniden UBC93XLT Scanner

Post by rustynswrail »

reena 20 wrote: Thu Mar 17, 2022 4:18 am I still use my Uniden UBC93XLT Scanner. I must say about it, old is Gold. :)
Nothing wrong with being old!

R
Post Reply