Hi guys,
Im thinking about setting up a outside antenna so that I can plug it into my Handheld scanner at home to get better reception/coverage of the metropolitan area.
I am considering using some sort of gutter mount for the antenna but would like to know if anyone else has a home setup and how they have done it.
Thanks in advance.
Daz
Home Scanner Setup
Moderator: Always RX
Home Scanner Setup
Per Ardua-Ad Astra
I've always used a discone mounted on a TV antenna pole, with the pole attached to a side wall with dynabolts. It's the same set-up a TV antenna installer might do, but with a discone instead of a TV antenna.
Regardless of what sort of antenna you use, the cable is critical, especially at UHF. Over a long run (more than ten metres) use low-loss coax: RG-213 or even 9913 if you're dinkum. The best antenna can be rendered worthless if there isn't a good cable to allow the signal it catches to reach your receiver.
Regardless of what sort of antenna you use, the cable is critical, especially at UHF. Over a long run (more than ten metres) use low-loss coax: RG-213 or even 9913 if you're dinkum. The best antenna can be rendered worthless if there isn't a good cable to allow the signal it catches to reach your receiver.
This is my base setup:
I have a few cb's and and a commercial unit and a mobile/desk scanner. Of all these radios, even if plugged into the same antenna the Icom blows the rest away.
And this is my aerial array:
I have a 6bd 2.1m vertical with 15m of RG213 and a 4.5db stainless to the side with 15m of RG58 and a 16 element beam wqith 10m of RG213. I also have 2 aerials mounted with gutter mounts on the gutter because the antennas on the array are useless when transmitting because there's not enough seperation and they get overloaded so i use the gutter mount aerials for when i want to listen to my scanner/other cb WHILE talking...
The beam is a very good listening scanner when pointed the right way. I can point it west of my location and hear the darling downs SES repeater link system which is about 400-500klm from my location. Once again, the icom only allows me to her it.
A scanner is a good radio but when you know the freq and want top or weak signals a 'dedicated' radio which only receives that band is best.
I have a few cb's and and a commercial unit and a mobile/desk scanner. Of all these radios, even if plugged into the same antenna the Icom blows the rest away.
And this is my aerial array:
I have a 6bd 2.1m vertical with 15m of RG213 and a 4.5db stainless to the side with 15m of RG58 and a 16 element beam wqith 10m of RG213. I also have 2 aerials mounted with gutter mounts on the gutter because the antennas on the array are useless when transmitting because there's not enough seperation and they get overloaded so i use the gutter mount aerials for when i want to listen to my scanner/other cb WHILE talking...
The beam is a very good listening scanner when pointed the right way. I can point it west of my location and hear the darling downs SES repeater link system which is about 400-500klm from my location. Once again, the icom only allows me to her it.
A scanner is a good radio but when you know the freq and want top or weak signals a 'dedicated' radio which only receives that band is best.
The Discone is an Excellent Antenna to use and it has a wide frequency coverage and there is a few good Discones and these are the Discones that I use 1/COMET-DS3000,1/DIAMOND-D150,2/ICOM-AH7000,they all work well but the ICOM does cost more and you do get 50 feet of good quality low loss cable from Japan with 2 N/TYPE connectors.
Regards Lino.
Regards Lino.