Excellent thanks, yes I have now tried the latest nightly release and changing frequencies on the fly works fine. Yes originally I downloaded the special XP version of Zadig so no issues there, I did download the latest nightly via the auto download batchfile however didn't use the Zadig from that obviously as it wasn't for XP.
Yep I saw the default plugins on the left, I'll give some from those sites a go thanks for that.
How to 'build a $19 scanner'
Moderator: Always RX
Re: How to 'build a $19 scanner'
"VKI, NJ050 will you be attending the job?"
"Negative VKI, my desk is bolted to the floor".
WARSUG General Scanning Moderator
"Negative VKI, my desk is bolted to the floor".
WARSUG General Scanning Moderator
Re: How to 'build a $19 scanner'
Couple of small issues, one being when I start SDR# it comes up three times with an ASIO something something error and I have to press OK each time, does this happen to anyone else?
Also again this might be a PC problem but I tried plugging in a second device and it blue screens XP every time Tried different ports, then one at a time installing the driver first then plugging them both in and bam BSOD...
Also again this might be a PC problem but I tried plugging in a second device and it blue screens XP every time Tried different ports, then one at a time installing the driver first then plugging them both in and bam BSOD...
"VKI, NJ050 will you be attending the job?"
"Negative VKI, my desk is bolted to the floor".
WARSUG General Scanning Moderator
"Negative VKI, my desk is bolted to the floor".
WARSUG General Scanning Moderator
-
- Moderator
- Posts: 2993
- Joined: Sat Feb 09, 2008 10:06 am
- Amateur callsign: VK6UFO_VK6RN
- Scanners and Receivers:
Scanners/receivers
Diamond Welz WS1000 wideband handheld
Radioshack Pro 28 handheld
Uniden UBC72XLT handheld
Uniden UBC73XLT handheld
Uniden UBC330CRS desktop
Two-way
Yaesu VX-3R 2m/70cm Ham TRX and wideband RX handheld
Yaesu FT-1802M 2m Ham TRX mobile x 2
Yaesu FT-7800R 2m/70cm Ham TRX and wide band RX mobile
Icom IC-208H 2m/70cm Ham TRX and wide band RX mobile
Icom IC-706MKIIG all-band all-mode Ham TRX mobile
Icom IC-V85 2m VHF Ham TRX handheld
Wouxun KG-UVD1P VHF/UHF wideband Ham TRX handheld
Wouxun KG-679P VHF wideband Ham TRX handheld
Wouxun KG-713 UHF wideband Ham TRX handheld - Location: Just on the border of your waking mind
Re: How to 'build a $19 scanner'
No. Can you post a screencap? One thing that was trapping people.. using a dongle with a remote control. The radio and the remote come up as separate items. They were installing the zadig driver to both and that was causing some issues.yorky wrote:Couple of small issues, one being when I start SDR# it comes up three times with an ASIO something something error and I have to press OK each time, does this happen to anyone else?
It BSOD as soon as you plug the second one into the USB port? Sounds like driver issues. Did you install the TV drivers that came with the dongle? If so, it might be worth uninstalling those. I found that some brands of dongle will use the Zadig driver on one port and the TV drivers on other ports. For me, it lets me SDR on one port then swap over and watch TV on other ports but I haven't tried multiple dongles (yet).yorky wrote:Also again this might be a PC problem but I tried plugging in a second device and it blue screens XP every time Tried different ports, then one at a time installing the driver first then plugging them both in and bam BSOD...
The yahoo sdrsharp group was full of people having weird issues depending on the OS, dongle type, 32 or 64 bit, shoe size and who knows what else. I quit yahoo so not sure what it's like now.
Rob
OF78WD
Amateur moderator
.
→Arguing with a fool proves there are two
OF78WD
Amateur moderator
.
→Arguing with a fool proves there are two
Re: How to 'build a $19 scanner'
I have a feeling the ASIO error (while it doesn't seen to make any problems its just a pain to hit ok three times on start) might be to do with a previously installed Creative sound card. This PC is now using its onboard audio and even though the Creative software was uninstalled there might be something left behind, not to worry really.
When you say the radio and remote come up separate, is that to do with Interface 0 and Interface 1? I installed the driver to both as one of the instructions said it was best to. I bought the one from your first link with the remote.
It BSOD's after a few seconds of the second dongle being inserted (pops up detected new device first so some sort of driver issue I'm guessing). I did not touch any drivers that came with it at all as I know they can cause issues. Tried a few different ports and installed the Zadig drivers to a couple of different ports although it didn't ask for drivers it somehow transferred its Zadig driver to the other port without hitting install but tried the re-install driver option anyway to make sure.
When you say the radio and remote come up separate, is that to do with Interface 0 and Interface 1? I installed the driver to both as one of the instructions said it was best to. I bought the one from your first link with the remote.
It BSOD's after a few seconds of the second dongle being inserted (pops up detected new device first so some sort of driver issue I'm guessing). I did not touch any drivers that came with it at all as I know they can cause issues. Tried a few different ports and installed the Zadig drivers to a couple of different ports although it didn't ask for drivers it somehow transferred its Zadig driver to the other port without hitting install but tried the re-install driver option anyway to make sure.
"VKI, NJ050 will you be attending the job?"
"Negative VKI, my desk is bolted to the floor".
WARSUG General Scanning Moderator
"Negative VKI, my desk is bolted to the floor".
WARSUG General Scanning Moderator
-
- Moderator
- Posts: 2993
- Joined: Sat Feb 09, 2008 10:06 am
- Amateur callsign: VK6UFO_VK6RN
- Scanners and Receivers:
Scanners/receivers
Diamond Welz WS1000 wideband handheld
Radioshack Pro 28 handheld
Uniden UBC72XLT handheld
Uniden UBC73XLT handheld
Uniden UBC330CRS desktop
Two-way
Yaesu VX-3R 2m/70cm Ham TRX and wideband RX handheld
Yaesu FT-1802M 2m Ham TRX mobile x 2
Yaesu FT-7800R 2m/70cm Ham TRX and wide band RX mobile
Icom IC-208H 2m/70cm Ham TRX and wide band RX mobile
Icom IC-706MKIIG all-band all-mode Ham TRX mobile
Icom IC-V85 2m VHF Ham TRX handheld
Wouxun KG-UVD1P VHF/UHF wideband Ham TRX handheld
Wouxun KG-679P VHF wideband Ham TRX handheld
Wouxun KG-713 UHF wideband Ham TRX handheld - Location: Just on the border of your waking mind
Re: How to 'build a $19 scanner'
Yes, interface 0 and 1. The first one is always the tuner and the second one is the remote for those dongles. It could be the reason why you're having issues. You should be able to remove the driver using device manager. Mine (Win7) shows the device in the "Universal Serial Bus devices" as "Bulk-In, Interface (Interface 0)". Presumably you will have similar and an entry for Interface 1 as well.yorky wrote:When you say the radio and remote come up separate, is that to do with Interface 0 and Interface 1? I installed the driver to both as one of the instructions said it was best to. I bought the one from your first link with the remote.
As for the Creative driver, you might be able to flush those out by booting into safe mode, then go into device manager to find all the installed but unused drivers. I seem to remember you can do that on XP.
Rob
OF78WD
Amateur moderator
.
→Arguing with a fool proves there are two
OF78WD
Amateur moderator
.
→Arguing with a fool proves there are two
Re: How to 'build a $19 scanner'
Bugger, I killed the Interface 1 in device manager but still blue screens when I plug the second stick in when it starts looking for a driver automagicly...
"VKI, NJ050 will you be attending the job?"
"Negative VKI, my desk is bolted to the floor".
WARSUG General Scanning Moderator
"Negative VKI, my desk is bolted to the floor".
WARSUG General Scanning Moderator
-
- Moderator
- Posts: 2993
- Joined: Sat Feb 09, 2008 10:06 am
- Amateur callsign: VK6UFO_VK6RN
- Scanners and Receivers:
Scanners/receivers
Diamond Welz WS1000 wideband handheld
Radioshack Pro 28 handheld
Uniden UBC72XLT handheld
Uniden UBC73XLT handheld
Uniden UBC330CRS desktop
Two-way
Yaesu VX-3R 2m/70cm Ham TRX and wideband RX handheld
Yaesu FT-1802M 2m Ham TRX mobile x 2
Yaesu FT-7800R 2m/70cm Ham TRX and wide band RX mobile
Icom IC-208H 2m/70cm Ham TRX and wide band RX mobile
Icom IC-706MKIIG all-band all-mode Ham TRX mobile
Icom IC-V85 2m VHF Ham TRX handheld
Wouxun KG-UVD1P VHF/UHF wideband Ham TRX handheld
Wouxun KG-679P VHF wideband Ham TRX handheld
Wouxun KG-713 UHF wideband Ham TRX handheld - Location: Just on the border of your waking mind
Re: How to 'build a $19 scanner'
The only other thing I can suggest is uninstalling the Zadig drivers completely and start again.
Also...
Also...
Rob
OF78WD
Amateur moderator
.
→Arguing with a fool proves there are two
OF78WD
Amateur moderator
.
→Arguing with a fool proves there are two
-
- 150+ posts
- Posts: 223
- Joined: Sun Dec 09, 2007 2:33 pm
- Amateur callsign: VK6FITN
- Scanners and Receivers: RTL2832U with RTL_Airband
Tait 8200 - Location: Bakers Hill
- Contact:
Re: How to 'build a $19 scanner'
For those that are interested, I've managed to get SDRSharp working for my feed.
Lots of learning for me, but it works now - Yay!!
Now I need a second DVB-T to scan the not-so-critical frequencies in the area....
Lots of learning for me, but it works now - Yay!!
Now I need a second DVB-T to scan the not-so-critical frequencies in the area....
Colin.
-
- 150+ posts
- Posts: 218
- Joined: Thu Aug 28, 2014 8:23 pm
- Scanners and Receivers: Uniden EZI30XLT Scanner.
Bearcat UBC355XLT - Location: High Wycombe
Re: How to 'build a $19 scanner'
Found this thread thanks to Yorky.
Use Linux.
Linux is a lot better at communicating with hardware than Windows is and ever will be.
Use Linux.
Linux is a lot better at communicating with hardware than Windows is and ever will be.
WASES CSU
Re: How to 'build a $19 scanner'
Thread revival!
Thinking into this a bit more lately and thinking about having a go again on a new PC as the old one that BSOD'ed and played up on XP went in the bin.
Anyone had any recent experience with the latest version of the software?
The outcome I'm looking at doing, is multiple frequencies (so multiple dongles) and then multiple upload streams to something like Broadcastify (or even something that you could connect straight to home if only used for yourself). Say 4+ streams.
Also looking at it being recorded locally and a way to easily playback remotely.
Thinking into this a bit more lately and thinking about having a go again on a new PC as the old one that BSOD'ed and played up on XP went in the bin.
Anyone had any recent experience with the latest version of the software?
The outcome I'm looking at doing, is multiple frequencies (so multiple dongles) and then multiple upload streams to something like Broadcastify (or even something that you could connect straight to home if only used for yourself). Say 4+ streams.
Also looking at it being recorded locally and a way to easily playback remotely.
"VKI, NJ050 will you be attending the job?"
"Negative VKI, my desk is bolted to the floor".
WARSUG General Scanning Moderator
"Negative VKI, my desk is bolted to the floor".
WARSUG General Scanning Moderator
-
- Posts: 110
- Joined: Mon Nov 21, 2005 10:22 pm
- Scanners and Receivers: AOR 8200 MKIII
- Location: Jandakot
Re: How to 'build a $19 scanner'
Hi Yorky,
Did you get any further with this?
Would be interested to know the hardware/software you used.
Cheers
--Steve
Did you get any further with this?
Would be interested to know the hardware/software you used.
Cheers
--Steve
End of Line
Re: How to 'build a $19 scanner'
Unfortunately not.
"VKI, NJ050 will you be attending the job?"
"Negative VKI, my desk is bolted to the floor".
WARSUG General Scanning Moderator
"Negative VKI, my desk is bolted to the floor".
WARSUG General Scanning Moderator
-
- Site Admin
- Posts: 2610
- Joined: Thu Feb 24, 2005 10:33 pm
- Amateur callsign: VK6HGR
- Scanners and Receivers: Various Yaesu, Kenwood, Tait, Simoco and Philips'
- Location: Perth, Western Australia
- Contact:
Re: How to 'build a $19 scanner'
The software has really improved over the last few years and it's (almost) plug'n'play now. The hard part is getting rid of the Windows TV drivers for the tuner stick and installing the WinUSB driver so it works with SDR# etc, and calibrating them because the <$10 devices have a substantial frequency error.
Got some very interesting data decodes. The RDS traffic data being transmitted on the commercial FM broadcast channels was easy to decode (sadly, the locations are encrypted)
The stability of the drivers and the frequency drift is still pretty high for the cheap tuner sticks that I wouldn't consider replacing the real radios on the streams with them but apparently the ~$30 ones in metal boxes have stable TXCOs in them and are much better.
Got some very interesting data decodes. The RDS traffic data being transmitted on the commercial FM broadcast channels was easy to decode (sadly, the locations are encrypted)
The stability of the drivers and the frequency drift is still pretty high for the cheap tuner sticks that I wouldn't consider replacing the real radios on the streams with them but apparently the ~$30 ones in metal boxes have stable TXCOs in them and are much better.
Gavin Rogers; VK6HGR
http://vk6hgr.ampr.org/
WARSUG forum administrator
Site and stream donations: https://www.paypal.me/vk6hgr
http://vk6hgr.ampr.org/
WARSUG forum administrator
Site and stream donations: https://www.paypal.me/vk6hgr